Happymodel Mobeetle6 65mm 1S AIO F4 Flight Controller Built-in OPENVTX Whoop and Toothpick 2in1 FPV Racing Drone BNF w/ SE0702 23000KV Motor
The DiamondF4 Flight controller and The Mobeetle6 were inspired from Angry Don FPV, we really appreciated for his help to Happymodel and to this hobby. We also very expecting to the performance of this BNF with the new Diamond F4 ELRS flight controller.
Specifications:
Brand Name:Happymodel
Item Name:Mobeetle6 whoop and toothpick 2-IN-1 FPV Racer Drone
Wheelbase:65mm
Size:80mm*80mm*30mm
Weight:17.5g (without battery)
Features:
The lightest 1S Whoop and Toothpick 2-IN-1 fpv drone
Comes with tooth pick frame for convert
Powerful and efficiency
The lightest 1s AIO 5IN1 F4 flight controller
New Unibell SE0702 brushless motors with pcb wire board
Built-in OPENVTX up to 400mw
Low profile Canopy design
| Motor | Mode:SE0702 KV23000 Configu-ration:9N12P Stator Diamter:7mm Stator Length:2mm Shaft Diameter:??1mm Motor Dimension(Dia.*Len):??9.5mm*14mm Weight(g):1.5g No.of Cells(Lipo):1S only |
| Propeller | Weight:0.19g Material:PC Pitch:1 inch Props Dia:30mm Center Hole Dia:1mm |
| Flight controller | (ELRS SPI RX version)DiamondF4 ELRS FC Firmware target:CrazybeeF4SX1280 (Frsky SPI RX version) DiamondF4 FR FC Firmware target:CrazybeeF4FR MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor:MPU-6000 or ICM20689 or BMI270(SPI connection) Original whoop size compatible Power supply:1S battery input (DC 2.9V-4.35V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Betaflight OSD(SPI Control) Built-in 5.8G OPEN VTX Built-in SPI ELRS V2.0/Frsky receiver Built-in 5V 1A BEC |
| Onboard 4in1 ESC | MCU upgraded to EFM8BB21 Power supply:1S LiPo/LiPo HV Current:5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware:O_H_50_REV16_8.HEX Default protocol:DSHOT600 |
| Onboard SPI ExpressLRS 2.4GHz Receiver | Packet Rate option:50Hz/150Hz/250Hz/500Hz ExpressLRS Firmware version:V2.0 RF Frequency:2.4GHz Antenna:Enameled copper wire antenna Telemetry output Power:<12dBm Receiver protocol:SPI ExpressLRS Compatible with ExpressLRS V2.0 TX Module Couldn??t flash separately ExpressLRS firmware |
| Onboard Frsky SPI D8 receiver Version | SPI BUS receiver Frsky D8 compatible Compatible Non EU transmitter D8 model Channels:8ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground):200m~300m |
| Onboard 5.8g OPENVTX | Firmware version:OPENVTX Smartaudio v2.1 PIT Mode support RCE Mode support Channels:48ch Transmitting Power:0/RCE/25mw/100mw/400mw Power supply:DC 5V Current (5v):<650ma (400mw) |
| Runcam Nano3 | Model:RunCam Nano 3 Image Sensor:1/3′ CMOS Horizontal Resolution:800TVL Lens:2.3mm(M6.5) FOV 140?? Signal System:NTSC S/N Ratio:>50dB Electronic Shutter Speed:Auto Auto Gain Control (AGC):Auto Min. Illumination:0.01Lux@1.2F D-WDR:Auto Day/Night:Color Power:DC 3-5.5V Current:110mA@5V 120mA@3.3V Housing Material:ABS Net Weight:1.2g Dimensions:L14mm*W14mm*H9mm |
| Lipo Battery | Capacity:300mAh Voltage:3.8v Continuous Discharge Rate:30C Size:57mmx12mmx7mm Weight:7.5g Connector:PH2.0 |
Package Included:
1x65mm whoop Frame (Mobula6 frame)
1x 65mm toothpick frame(Mobeetle6 frame)
Option1:DiamondF4 ELRS built-in SPI ELRS receiver
Option2:DiamondF4 FR built-in SPI FRSKY receiver
4x SE0702 KV23000 Unibell brushless motor
1xGemfan 1210 31mm propeller(4cw+4ccw)
1x Runcam Nano3
1x Built-in 5.8G 48ch 25mw-400mw OPENVTX
2x 1s 300mah Lipo battery
1x Mobula6 canopy
1x Propeller disassemble tool
1x Screwdriver
Additional information
| Weight | 0.1 kg |
|---|---|
| Receiver: No selection | ELRS 2.4GHz, FRSKY |
Reviews